A Swivel is a mechanical device used on a drilling rig that hangs directly under the traveling block and directly above the kelly drive, which provides the ability for the Kelly (and subsequently the drill string) to rotate while allowing the traveling block to remain in a stationary rotational position (yet allow vertical movement up and down the derrick) while simultaneously allowing the introduction of drilling fluid into the drill string.Parts: bail, Gooseneck, upper shell, body, lower shell, swivel stem, shaft, sealing system, etc.

• API 8C standard;
• Swivel and Kelly spinner are combination;
• High strength steel ensure the service time and capacity;
• High pressure drilling fluid sealing system;
• With keyless connection adopted between spinner and central pipe of swivel

The hook is the important lifting equipment for drilling, the main functions of which are suspending and lifting the drill string, replacing the drill bit, dropping the casing, discharging the production of the slightly jammed drill, etc. It mainly consists of the Hook Rod, Sheave system, Body, etc.

• Designed to API 8C
• The frame used the High strength steel material
• Main hook installs the safety device
• The main parts are used the high-strength alloy steel.
• Sheaves groove through the heat treatment, Improves surface hardness, wear resistance, and service
• The brake system can adjust 360º
• The hook can lock automatically when the swivel hanging.

The traveling block is the free section of the block that contains a set of pulleys or sheaves through which the drill line ( wire rope) is threaded and opposite the crown block. It includes the single sheave and double sheave systems.Designed to API 8C

• Frame used the High strength steel material
• Main hook install the safety device
• Main parts are used the high strength alloy steel.
• Sheaves groove through the heat treatment, Improve surface hardness, wear resistance and service

A rotary table is a mechanical device on a drilling rig that provides clockwise (as viewed from above) rotational force to the drill string to facilitate the process of drilling a borehole.Design and manufactureaccording to API 7K standard.Bevel gear pair use the spiral bevel gear, stable transmission, high capacity

• Gear material is alloy steel, Main shell is iron
• Long service time,
• We also can be produce accordingto your request.

A Draw works are the primary hoisting machinery that is a component of a rotary drilling rig. Its main function is to provide a means of raising and lowering the traveling blocks. The wire-rope drilling line winds on the draw work drum and extends to the crown block and traveling blocks, allowing the drill string to be moved up and down as the drum turns. The segment of the drilling line from the draw-works to the crown block is called the “fast line”. The drilling line then enters the sheaves of the crown block and it makes several passes between the crown block and traveling block pulleys for mechanical advantage.

• The line then exits the last sheave on the crown block and is fastened to a derrick leg on the other side of the rig floor. This section of the drilling line is called the “deadline”.
• All sheaves and shafts are made of alloy steel.
• Chains are pressure lubricated.
  3. Drum is grooved. The low-speed & high-speed ends of the drum shaft are equipped with ventilating pneumatic tube clutch.
• The brake rim (or disc) is water cooled and the surface is medium-frequency induction hardened that provides excellent wear-resistance capacity and long service life.

Air winches are powered by a piston-type air motor. They have the advantages of compact structure, are lightweight, safe, and easy to operate, and they are used for general lifting, hauling, and other works in mines, oil fields, on shipboards and etc. Mainly consist of the Air motor, gearbox, cylinder, brake system, frame, etc.

• Piston type air motor used the double supporter design;
• Operation rod can be adjusted with infinite speed variation;
• The main parts used the high strength steel;
• Wireline can be provide
• Design and produce according to the API 7K standard

The bucking unit is a kind of threaded connection handing unit, that can be used in downhole pump, downhole tools, tubing, casing, and negotiation thread connection of manufacturing assembly and maintenance. Master tong and backup tong fastening the pipe by two way, widely range, and do not replace the accessories;

1. Hydraulic operation:
2. Master tong and backup tong Synchronous work;
3. Torque automatic system;
4. Backup tongs can b

Drilling hose(rotary hose)made according to API 7K spec, applies for flexible hose connection between the top of oil drilling standpipe and vertical moved to the swivel joint in well drilling, well cementing, work-over, and down-hole servicing operation. drilling hose is also used to adjust the installation mistake between drilling pipeline and standpipe to avoid shake, sometimes to transfer high-pressure oil and water base mud with the lowest aniline point of 60°C from the swivel pipe in high pressure, and down-hole operation high medium such as water, oil, etc, drilling rotary hose can be used for perfect work too.

HPU is the power source for generating the flow of hydraulic fluid for the desired application. That being said, the combinations are endless and at advanced fluid power, we design and build custom power units to the specification of the customer. Mainly consist of motor, pump, coupling, adjustable pressure control, pressure gauge, reservoir, etc.

• Can be used in onshore and offshore drilling operation, desert and continuous workingsituation;
• Wide adjustment range, easy operation, high generality;
• Air or water cooled;
• Electricdriver and diesel drive

Deadline anchor is used as a display instrument for indicating and recording the drilling string changes in weight and pressure, helping the driller to master the working parameter and judge the drilling state in the drilling operation. It’s mainly composed of two parts: Body and Senor. It works together with the Weight indicator.

• Can be used in drilling rig, workover drilling rig etc.
• Material is High strength steel, extended the service time.
• 5 times pressure and tensile test before leaving the factory, high precision, stability, etc.
• Two forms, horizontal and vertical.

Weight indicator suitable for drilling and geological exploration drilling rig or workover process instructions and record the drilling hanging weight and WOB change, it can help drillers to master the working parameters and judge the working state of drilling tools. Weight indicator by the deadline anchor, weight secondary table (weight indicator and recorder). The instruments work environment temperature: -40~50.

• Can be used the drilling rig, workover drilling rig etc;
• Hydraulic and electrical;
• Two types: horizontal and vertical
• Easy tooperate

Drilling steel wire rope is made of steel wire around a central steel wire and then twists by the rope stand around the cable core. Most of the drilling lines are steel cable core, which is divided into left-handed and right-handed, Material grade is IPS, EIPS, EEIPS, etc. To choose the drilling line according to the hook load, most of the model is 6*19S IWRC, the diameter is Ø22mm- Ø 30mm, and the Standard is API 9A and ISO10425.

• High metal filling factor and breaking force with a smoothly surface
• Best wear resistance, anti-extrusion performance
• Stability, long service time;
• Can use in drilling rig, workover drilling and operation etc.